How to Check Transmission Fluid Ford Escape?

The easiest way to check your Ford Escape’s transmission fluid is to pop the hood and locate the dipstick. With the engine running, pull out the dipstick and wipe it clean with a rag. Reinsert it all the way back in, then remove it again and check the level of fluid on the end.

If it’s between the “Full” and “Add” lines, you’re good to go. If it’s below the “Add” line, you’ll need to add more transmission fluid.

  • Park your Ford Escape on a level surface and set the parking brake
  • Locate the dipstick handle on the driver’s side of the vehicle, near the back of the engine
  • Pull out the transmission dipstick and wipe it clean with a rag or paper towel
  • Insert the dipstick all the way back into its tube, then pull it out again to check your transmission fluid level
  • If the fluid is at or below the “Add” line on the dipstick, you’ll need to add more transmission fluid to your car

Ford Escape Transmission Fluid Dipstick

If you own a Ford Escape, it’s important to know where the transmission fluid dipstick is located. This way, you can check the level of fluid and top it off if necessary. The dipstick is located on the passenger side of the engine, near the firewall.

It has a yellow handle that’s easy to spot. To check the fluid level, simply pull out the dipstick and wipe it clean with a rag. Then insert it back into the tube and pull it out again.

Check to see where the fluid level falls on the stick. If it’s at or below the “Full” line, then you’ll need to add more fluid. Adding transmission fluid is easy – just open up the hood and locate the fill port (it will have a cap with “TF” or “Transmission Fluid” written on it).

Remove the cap and use a funnel to pour in new fluid until it reaches the “Full” line on the dipstick. Replace the cap when finished.

2017 Ford Escape Transmission Dipstick Location

If you’re looking for the transmission dipstick on a 2017 Ford Escape, you’ll find it near the back of the engine, on the passenger side. It’s a long, thin metal rod with a handle on one end and a small loop on the other.

To check your transmission fluid level, first find the fill line (it will be marked on the dipstick) and then insert the dipstick all the way into the transmission fluid reservoir.

If necessary, wipe off any fluid that might be on the dipstick before withdrawing it and checking the level against the fill line. Add fluid if necessary to bring it up to the full mark.

2014 Ford Escape Transmission Dipstick Location

If you’re looking to check the transmission fluid in your 2014 Ford Escape, you’ll need to locate the dipstick first.

The good news is that it’s easy to find – it’s located near the front of the engine, on the left side. Simply pull out the dipstick, wipe it clean, insert it again and remove it once more to check the fluid level.

If it’s low, add more until it reaches the “full” line on the dipstick. Easy as that!

2008 Ford Escape Transmission Fluid

If you own a 2008 Ford Escape, it’s important to keep an eye on your transmission fluid level. A drop in fluid level can indicate a leak, and if left unchecked, can lead to transmission failure. Here’s how to check your transmission fluid level:

1. Park your Escape on a level surface and set the parking brake.

2. Start the engine and let it idle for a few minutes to warm up the transmission fluid.

3. Locate the dipstick handle – it should be on the driver’s side of the engine compartment, near the firewall.

4. Pull out the dipstick and wipe it clean with a rag or paper towel.

5. Insert the dipstick all the way back into its tube, then pull it out again and check the fluid level against the markings on the dipstick (full = hot; full = cold). 6. If necessary, add transmission fluid to bring the level up to “full.”

Use only Ford-approved Mercon LV ATF (automatic transmission fluid). Never overfill – too much fluid can cause damage!

How Do You Check the Transmission Fluid in a 2013 Ford Escape?

Assuming you would like a step-by-step guide on how to check the transmission fluid in a 2013 Ford Escape:

1. Park your Ford Escape on level ground and turn off the engine. Let your car sit for a few minutes so the transmission fluid has time to settle.

2. Find the transmission dipstick. In most Ford Escapes, it’s located near the back of the engine on the passenger side. It will have a yellow or orange handle and will likely be labeled “TRANS.”

3. Pull out the dipstick and wipe it clean with a rag.

4. Reinsert the dipstick all the way, then pull it out again to check the fluid level. The dipstick should have two markings that indicate full and low levels of fluid; if the fluid falls between these two marks, it’s at an acceptable level.

Where Do You Put Transmission Fluid in a 2013 Ford Escape?

If you’re looking to add transmission fluid to your 2013 Ford Escape, you’ll need to locate the dipstick. The dipstick is usually located near the front of the engine, on the passenger side. Once you’ve found it, pull it out and wipe it off with a clean cloth.

Then, reinsert it and remove it again to check the fluid level. If the level is low, add transmission fluid until it reaches the “Full” line on the dipstick.

How Do You Check the Transmission Fluid on a 2012 Ford Escape?

Transmission fluid is vital to your car’s operation. It helps to keep the transmission cool and lubricated, and ensures proper shifting.

Checking the transmission fluid on your 2012 Ford Escape is a simple process that can be done in just a few minutes.

To check the transmission fluid, start by opening the hood and locating the dipstick. The dipstick will have a red or pink handle, and will likely be labeled “transmission.” Pull out the dipstick and wipe it clean with a rag.

Then, reinsert it fully into the Transmission Fluid Dipstick Tube before removing it again to check the level. The transmission fluid should be at or near the “Full” line on the dipstick. If it is below this line, you will need to add more transmission fluid.

To do so, locate the fill plug on the side of the transmission (it will have a yellow cap). Remove this cap and use a funnel to pour new transmission fluid into the opening until it reaches the “Full” line on the dipstick. Replace the fill plug when finished, then start up your engine and check for leaks.

How Do You Check the Transmission Fluid on a 2007 Ford Escape?


Your car’s manual will tell you when to do it, but it’s usually every 30,000 miles or so. Checking and changing your transmission fluid is easy and only takes a few minutes. Here’s how:

1. Park your car on level ground and turn it off. Locate the dipstick near the back of the engine, towards the driver’s side.

2. Pull out the dipstick and wipe it clean with a cloth or paper towel. Reinsert it all the way and then pull it out again to check the fluid level

3. The dipstick will have two marks on it, “full” and “low.” If the fluid reaches the full mark, you’re good to go.

If it’s below that mark, you’ll need to add some more fluids before continuing driving. 4. To add fluids, find the transmission fluid reservoir (it will be clearly labeled).

Conclusion

The transmission fluid in your Ford Escape is important for the proper functioning of your vehicle. Checking it regularly can help you avoid problems down the road. To check your transmission fluid, simply remove the dipstick, wipe it off, reinsert it, and then check the level.

If it’s low, add more until it reaches the “full” mark.

Danyl Dmitry

Leave a Comment