If your Harley shocks are in need of adjustment, there is no need to go out and purchase a special tool. All you need is a simple socket wrench. First, locate the two adjuster nuts on the top of the shock absorber.
These will be located just above the spring. Next, using your socket wrench, turn both nuts clockwise until they are tight.
Finally, check your owner’s manual for the proper amount of pre-load tension and adjust accordingly.
- Find the preload adjuster nut on top of each shock
- loosen the locknut that holds the preload adjuster in place
- turn the preload adjuster clockwise to increase preload, or counterclockwise to decrease it
- once you’ve achieved the desired setting, tighten the locknut back in place
Motorcycle Rear Shock Adjustment Without Tool?
If you’re a motorcycle enthusiast, then you know that one of the most important parts of your bike is the rear shock. This is what helps to absorb all of the bumps and jolts as you’re riding, and it’s essential for a smooth ride.
Unfortunately, adjusting the rear shocks can be a bit of a pain, especially if you don’t have the right tools.
Luckily, there’s a way to adjust your rear shocks without any tools at all!
Here’s how: 1) Park your bike on level ground and put it in gear so it doesn’t move.
2) Find the two nuts that hold the spring onto the shock absorber. These are usually located near the top of the shock.
3) Use your hands to turn both nuts counterclockwise until they’re loose enough to remove by hand. Be careful not to drop them!
4) Once both nuts are removed, carefully pull out the spring from its housing. You may need to use a little force, but be careful not to damage anything.
5) Now that the spring is out, take a look at how much pre-load is currently on it. This is simply how much tension has been placed on the spring by winding it up before installation. If you want to increase or decrease pre-load, simply wind or unwind accordingly before re-installing everything.
6) To reinstall, simply reverse steps 1-5!
How Do You Adjust a Harley Shock?
Assuming you would like tips on how to adjust the shocks on a Harley Davidson motorcycle: The first step is to find the right tools. You will need an adjustable wrench, a socket wrench, and a measuring tape.
Next, locate the adjustment screws. There are two of them, one on the top of each shock. Using the measuring tape, measure the distance from the center of the axle to the fender.
This is your starting point and will be used as a reference later. Now it’s time to begin adjusting. First, use the adjustable wrench to loosen the locknut on each adjustment screw.
Then, use the socket wrench to turn each screw until you’ve achieved your desired level of preload. Be sure to take note of how many turns you make so that you can replicate this number when adjusting the other side.
Finally, retighten each locknut using the adjustable wrench.
Once both sides are adjusted according to your preference, recheck your work by again measuring from the center of the axle to the fender. This number should match up with your original measurement from before making any adjustments. And that’s it!
You’ve now successfully adjusted your Harley Davidson motorcycle’s shocks!
What Psi Should Harley Air Shocks Be At?
Harley air shocks are designed to be inflated to a specific pressure, depending on the model of motorcycle. For example, the 2017 Sportster models have a recommended psi range of 25-35. The 2017 Dyna models have a recommended psi range of 30-40.
The 2017 Softail models have a recommended psi range of 35-45. Always refer to your owner’s manual for the specific psi recommendations for your Harley air shocks.
Can You Change Motorcycle Shocks Without a Jack?
No, you cannot change motorcycle shocks without a jack. You will need to use a jack to lift the motorcycle off of the ground in order to change the shocks.
How Do I Stiffen the Rear Shock on My Motorcycle?
There are a few ways to stiffen the rear shock on your motorcycle. One way is to adjust the preload. This can be done by turning the adjusting knob clockwise or counterclockwise.
Clockwise will increase the preload, while counterclockwise will decrease it. Another way to adjust the stiffness of your rear shock is by changing the spring rate. This can be done by installing a stiffer spring or by removing spacers from your existing spring.
Finally, you can also adjust the damping of your rear shock. This can be done by turning the rebound damping knob clockwise to increase stiffness, or counterclockwise to decrease it.
Conclusion
If you’re a Harley owner, you know that keeping your bike in tip-top shape is important. One way to do this is to adjust your shocks regularly. But what if you don’t have the right tools?
Never fear! You can still adjust your shocks without the proper tools. Just follow these simple steps and you’ll be up and running in no time.
First, remove the shock absorber from the bike. Next, find a suitable replacement that fits snugly into the mount.
Once you have the new shock in place, simply tighten or loosen the mounting bolts until it’s tight enough for your liking.
That’s all there is to it! Now get out there and enjoy the ride knowing that your shocks are properly adjusted.
- Difference between Bilstein 5100 Vs 6112 - April 15, 2023
- Difference between Bilstein 5100 Vs Fox 2.0 - April 15, 2023
- Difference between Bilstein B4 Vs B6 Ride Quality - April 14, 2023