How to Clean Ignition Coil?
To clean your ignition coil, first disconnect it from the power source. Next, use a brush to remove any debris or build-up on the coil. Once the coil is clean, reconnect it to the power source and test it to…
How to Remove Windshield Washer Fluid Reservoir?
To remove the windshield washer fluid reservoir, first disconnect the negative battery cable. Next, remove the wipers and wiper arms. Locate the three bolts that secure the reservoir to the firewall and remove them. Finally, pull the reservoir out of…
Caliper Vs Cantilever Brakes
There are two main types of brakes used on bicycles: caliper and cantilever. Caliper brakes are the more common type, consisting of two brake pads that clamp down on the wheel when the lever is pulled. Cantilever brakes have one…
Can Air in Brake Line Cause Caliper to Stick?
Yes, if there is air in the brake line it can cause the caliper to stick. When brakes are applied, fluid is forced from the reservoir into the caliper pistons. If there is a leak in the system, air can…
Can You Splice an Abs Sensor Wire?
No, you cannot splice an ABS sensor wire. The ABS sensor is responsible for monitoring the speed of the wheels and relaying that information to the ABS system. If the ABS sensor wire is damaged, it will need to be…
How to Install Caliper Brakes on Bicycle?
Installing caliper brakes on a bicycle is a simple process that can be completed in just a few minutes. First, remove the wheel from the bicycle and then use a 5mm allen key to loosen the bolts that secure the…
How to Release Brake Caliper Pressure?
If your brake caliper is sticking, you may need to release the pressure in the caliper. To do this, you will need a C-clamp and a piece of wood. Place the wood against the piston in the caliper and use…
How to Remove Ball Joint Rivets?
There are a few ways to remove ball joint rivets, but the most common is with a drill. First, you will need to drill out the old rivets. Be sure to wear safety goggles and gloves when doing this. Next,…
How to Remove Rear View Mirror Ball Joint?
The rear view mirror ball joint is located at the top of the windshield on the driver’s side. It is held in place by two screws. To remove it, first loosen the screws with a screwdriver. Then, pull the ball…
Why Won’T My Brake Caliper Piston Compress?
Your brake caliper piston may not be compressing for a variety of reasons. The most common reason is that the brake pads are worn out and need to be replaced. Other possible causes include: a build-up of rust or debris…
Difference Between Coilover Vs Lowering Spring
Coilover suspensions are a type of vehicle suspension that uses coilover springs. They are generally used in racing cars and performance vehicles. Lowering springs are a type of vehicle suspension that lowers the ride height of a vehicle. Lowered vehicles…
Do Bad Ball Joints Make Noise?
Bad ball joints can make a lot of noise. It may sound like a squeak or a grinding noise when you turn the steering wheel. The noise is caused by the wear and tear on the ball joint itself. If…
Do Coilovers Improve Ride Quality?
Yes, coilovers improve ride quality because they allow for adjustability and a more customized suspension. Coilovers also provide a firmer ride, which can improve handling on the road or track. Coilovers can improve the ride quality of your car by…
Do Coilovers Replace Struts?
Coilovers are a type of suspension that can replace your car’s struts. They offer adjustable ride height and damping, so you can tune them to your liking. Coilovers also tend to be lighter than struts, which can improve your car’s…
How to Fix Cigarette Burns in Car Headliner ?
To fix a cigarette burn in a car headliner, first remove the burned area with a pair of scissors. Then use a piece of sandpaper to lightly sand the area around the burn. Next, apply a thin layer of automotive…
How to Adjust Camber on Coilovers
There are a few ways to adjust camber on coilovers, but the most common is by adjusting the bottom mount. To do this, first loosen the bolts that hold the bottom mount in place. Next, rotate the bottom mount until…
How to Adjust Coilover Shocks
Coilover shocks are a type of suspension that uses springs and shocks together in a single unit. The coilover shock is mounted to the chassis of the vehicle and the spring is mounted around the shock. This allows for easy…
How to Adjust Coilovers Stiffness ?
There are a few ways to adjust coilovers stiffness, but the most common is to use a wrench or an Allen key. Most coilovers will have an adjustable knob that can be turned clockwise or counterclockwise to increase or decrease…
How to Adjust Height on Coilovers? Let’s find out!
Coilovers are a type of suspension system that combine the coil spring and shock absorber into one unit. Adjusting the height on coilovers is a fairly simple process that can be done with a few basic tools. First, you will…
Can a Bad Sway Bar Link Cause Vibration?
A sway bar link connects the sway bar to the suspension, and its main purpose is to keep the body of the vehicle level when cornering. If a sway bar link is worn out or broken, it can cause the…