To calibrate electric power steering, you will need to connect a voltmeter to the battery and ground the negative lead. With the engine off, turn the wheel all the way to one side and hold it for five seconds. Next,…
If your car’s engine has sludge build-up, it is important to clean it as soon as possible. Sludge can cause serious damage to your engine and lead to costly repairs. To clean engine sludge, you will need: – A bucket…
To clean your evap canister, first remove it from your vehicle. Then, using a garden hose, spray the canister down and scrub it with a brush to remove any dirt or debris. Next, rinse the canister off and allow it…
To clean your FCW sensor, you’ll need a soft cloth or cotton swab and some isopropyl alcohol. First, power off your device. Then, gently wipe the sensor with the cloth or swab until it’s clean. Finally, apply a small amount…
The hood latch sensor is located on the underside of the hood, near the latch itself. To clean it, simply use a cotton swab or Q-tip dipped in rubbing alcohol. Gently wipe away any dirt or debris from the sensor,…
To clean your ignition coil, first disconnect it from the power source. Next, use a brush to remove any debris or build-up on the coil. Once the coil is clean, reconnect it to the power source and test it to…
To clean Softex seats, first remove any loose dirt or debris with a vacuum cleaner. Next, mix a solution of mild soap and warm water. Use a soft cloth to wipe down the seats, being careful not to saturate them….
To clean a TPS sensor, first disconnect the battery and remove the sensor from the vehicle. Next, use a wire brush to clean any dirt or debris from the sensor. Once the sensor is clean, reconnect the battery and test…
To disable steering wheel lock, open the car door and insert the key into the ignition. Turn the key to the “on” position, then press and hold the unlock button on the steering wheel. After a few seconds, the steering…
If your car’s caliper has seized, you will need to replace it. First, remove the old caliper by unbolting it from the suspension. Next, install the new caliper in the same location and bolt it into place. Finally, bleed the…
If the airbag sensor is not working, the airbag will not deploy in a crash. To fix an airbag sensor, first check the fuse and wiring to see if there are any broken wires or burnt out fuses. If everything…
If your auxiliary battery is not working properly, there are a few things you can do to fix it. First, check the battery terminals to make sure they are clean and free of corrosion. Next, check the fuse box for…
If the magnetic clutch is not functioning properly, there are a few things that can be done to troubleshoot and fix the problem. First, check the voltage at the terminals of the clutch. If the voltage is too low, it…
To fix peeling window tint, first try to use a razor blade or other sharp object to scrape off the loose pieces of tint. If that doesn’t work, you can use a heat gun or hair dryer to slowly heat…
The powertrain fault for Ford Fusion can be fixed by checking the transmission fluid level and if it is low, adding more transmission fluid. Checking the engine oil level and if it is low, adding more engine oil. Checking for…
If your car has radio controls on the steering wheel, and they are not working properly, there are a few things you can try to fix the issue. First, check to see if the fuse for the radio controls is…
If your service steering column lock light is on, it means that the system is not functioning properly. There are a few things you can do to fix this: 1) Check the fuse box and replace any blown fuses. 2)…
If your slip indicator light is on, it means that your car’s traction control system is not working properly. There are a few things you can do to fix this problem: 1. Check the fuse box for a blown fuse….
If your brakes feel like they are slipping or grabbing, you may need to adjust the brake pads. To do this, you will need to remove the wheel and access the brake pad. Once the brake pad is exposed, you…
The best way to fix window tint that is peeling is to remove the old film and replace it with new film. This can be done by a professional, or you can do it yourself. First, you will need to…
To remove bird poop from a car window, start by using a clean cloth or paper towel to blot up as much of the mess as possible. Next, make a mixture of warm water and dish soap and use it…
There are a few ways to remove dents from leather seats. One is to use a vacuum cleaner with the hose attachment. Put the hose over the dent and turn the vacuum on high. The suction will pull the dent…
There are a few ways to remove gum from a car door. One way is to use WD-40. WD-40 is a lubricant that can be found at most hardware stores. Spray the WD-40 onto the gum and let it sit…
There are a few ways to remove gum from a leather car seat. One way is to use ice. Place an ice pack or bag of frozen peas on the gum for a few minutes. The gum should harden and…
To get rid of gnats in your car, clean all surfaces with soapy water. This will remove any food or dirt that the gnats are attracted to. Then, use an insecticide spray or gel on all surfaces, paying special attention…
A pilot bearing is a small ball or roller-type bearing located in the end of the crankshaft. Its purpose is to support and guide the main drive shaft as it enters the transmission. The pilot bearing must be installed prior…
There are a few things you can do to make your 2WD truck better in the snow. First, make sure you have good tires with plenty of tread. Second, use a weight distribution hitch to help distribute the weight of…
If the mass air flow (MAF) sensor is not providing the correct signal to the engine control unit (ECU), it will need to be modified. The first step is to identify the problem with the MAF sensor. This can be…
If you need to remove a pulley without a puller, there are a few things you can try. One is to use a screwdriver to pry the pulley off the shaft. Another is to use a hammer and punch to…
To remove a relay from your fuse box, start by unscrewing the lid of the box and removing it. Inside, you should see a diagram labeling each fuse and relay. Locate the relay you need to remove, and use a…